1V Prewired Harness, 2 Pickup Standard, 1Vol 3Way Switch Toggle
Click To Enlarge

1V Prewired Two Pickup Harness
1 Pot Standard Wiring Harness
For HH, HS, or SH Standard Systems
Works Great for So-Cal /Charvel Styles
1 Standard Volume Control Pot Only
3 Way Standard Toggle Switch ~ Standard Jack
Pre-Wired Electric Guitar Wiring Harness

These customized hand-wired Volume Pot Harnesses work well with most Two Pickup (i.e. Humbucker-Humbucker or Humbucker-Single) Systems. These single pot harnesses are designed for players seeking a minimized, uncluttered control field and are great for SoCal / Charvel® Style systems. Each harness is unique and, based on order style/selections as well as current component stock on hand, will vary in appearance from the sample images. Read all product information carefully and ask any questions before you buy.

This prewired harness features the following default options. Your menu selections may vary and we will wire to order.
*1 Standard 3 Way Open Toggle Switch (choice of colors)
*1 Standard 500K Large/Long Full Size Volume Control Pot
*1 Standard Mono Style Jack
Customizable Options & Upgrades Available!

The included Open Style 3-Way Toggle Switch (LP / Gibson Switch Style) provides standard 3 Way pickup selections allowing for Bridge/Bridge-Neck/Neck options. Your choice of toggle switch shaft/handle & tip color.

Pot selections are available in full size Large (Quarter Size) or Small (Dime Size) as well as Short Shaft (~15mm) for plate/guard mounting or Long Shaft (~18mm) for body mounting. If you are going through a guard and body or have a non-standard set-up, you may need additional nuts or washers for adjustment (sold separately) or other modification. Longer life brass bushings, extra-long shafts, CTS styles and Push-Pull options are options in some configurations.

Audio Taper (“A” pot) or Linear Taper (“B” pot) styles are available. Players will often use B Pots for the volume. We also offer your choice of OHM style. Traditionally, humbuckers are paired with 500K pots and single coil pickups with 250K pots. If you are coil splitting, we do not recommend 250K. 25K pots are used with active pickups and, if selected, include an upgrade from Mono Jack to Stereo Jack plus a Battery Clip (with ~ 150mm wire lead).

Depending on style and what you are looking for in terms of performance, you might vary from these standards. Results will vary at your risk (exercise extreme discretion!).

Harness jacks work with standard cables only and jack sockets accept standard ¼” plugs. Your choice of jack style:
*Mono Jack (9mm mounting hole; tightens to your jack plate)
*Stereo Jack (9mm mounting hole; tightens to your jack plate)
*Barrel Jack (12mm mounting hole; tightens inside of guitar)
*Switchcraft Jack (10mm mounting hole; tightens to jack plate)

Installation requires soldering. Basic instructions are posted in the item images to show the solder connections needed. Please know your abilities, requirements, measurements and needs to make sure this item will work for you. We are available to answer any questions before you buy.

We wire each harness to order and offer many style and upgrade options along with typical replacements in standard and left-handed versions. We can accommodate many styles and preferences. Check our Store Wiring Harness page or contact us for product variations or questions and additional options if needed.

*Switch Shaft Diameter: 11.7mm
*Overall Switch Height: 50mm
*Switch Insertion Depth: 23mm
*Switch Base Diameter: 17mm
*Standard Pot Shaft Length: 18mm
*Standard Pot Diameter: 24mm
*Standard Pot Height: 30mm
*Standard Pot Hole Diameter Required: 10mm
*Standard Pot Depth Required: 12mm
*Standard Mono Jack Length: 15mm (without pins)
*Standard Mono Jack Diameter (Mounting Hole Required): 9mm
*8” Insulated Wire Length
Variability is to be expected as measurements provided are approximations and based on the default options. Options selected will determine actual measurements. Depending on your system or set-up, modifications may be needed. Ask any questions regarding options, measurements, installation, requirements, special requests, etc. prior to purchase.

*1 Prewired Guitar Wiring Harness Kit
Nothing else is included. Additional images may be provided for reference and comparison purposes only. There are no hard copy instructions or diagrams included. Basic directions are provided in the product images.

OPTIONAL ADDITIONS (Further Customize Your Harness!)
The Kill Switch Wiring Option allows you to interrupt the signal using an on-off, two-way toggle style mini-switch (~5.85mm diameter; 6mm hole required).

The Series Parallel Wiring Option incorporates a two-way toggle style mini-switch (~5.85mm diameter; 6mm hole) so you can flip your humbucker between series/parallel. Choose Series-Parallel BRIDGE if you want this for your bridge and/or Series Parallel NECK for the neck. Four wire humbucker pickups are required for this wiring mod to work.

The Treble Bleed Volume Kit Wiring Modifier addresses loss of high-end signal when turning down your volume pot to keep more of your highs while maintaining volume adjustability. This option allows a more constant tone throughout the range of your volume pot and helps remove the dark muddiness typically experienced in the lower volume pot settings.

Buyers assume all risk of use; sales are only offered to those competent to safely and lawfully purchase and use items. ASK ANY QUESTIONS PRIOR TO PURCHASE. Due to the vast and varied nature of possible set-ups and user expertise, we do not provide specific information for every possible installation scenario. The provided BASIC instructions (posted in the item images, not sent as a hard copy with your order) will get you started. Please ask any questions before you buy if the posted instructions are not sufficient for your install or if you are unsure of your needs or ability to make modifications.

Note that we do not recommend installation using power tools as these can put too much force on the product and cause damage. Installation is best with moderate heat only (don’t have your iron too hot). Pay attention during install to avoid damage; components are sensitive. Excessive or prolonged heat can cause irreparable damage. This item is prewired. If your set-up requires you to disconnect the wires, be sure to take a picture or make note of the connections so you can reattach (solder!) properly. We do not recommend a clip/tie method for installation.

Inspect your order upon receipt. We will address any issues PRIOR to installation. Installation, modification, or use in any way invalidates the possibility of a return.

  • Item #: 1040

1V Prewired 2 Pickup Harness, 1 Standard Volume 3W Toggle Switch

Price: $21.95
* Marked fields are required.
Qty: *
Reviews (0) Write a Review
No Reviews. Write a Review