1V2T Prewired Harness, 2 Pickup CTS PUSH-PULL w/ DUAL Coil Split
Click To Enlarge

1V2T Prewired 2 Pickup Harness
3 Pot HH Two Pickup CTS Premier Harness
1 CTS Vol. Control Pot + 2 CTS Push-Pull Tone Pots
FCS 3 Way Blade Switch ~ Switchcraft Mono Jack
Pre-Wired Electric Guitar Wiring Harness

INDEPENDENT Coil Cut Controls
Control Each Pickup Separately!

These customized hand-wired harnesses work well with Two Pickup (i.e. Humbucker-Humbucker) Systems. We offer many style and upgrade options as well as typical replacements in standard and left-handed made-to-order wire harness versions. Each harness is unique and, based on order selections as well current component stock on hand, may vary in appearance from the sample images.

This prewired harness features the following default options. Your menu selections may vary and we will wire to order.
*1 Fender® Custom Shop (FCS) 3 Way Blade Switch
*1 CTS Precision 500K Large/Long Volume Control Pot
*2 Precision CTS Push-Pull 500K Large/Long Tone Pots
*1 Sprague Orange Drop 0.047 Tone Cap
*1 Switchcraft #11 Jack
*1 Jig (protects wiring during transit)
*3 Knobs (choice of colors)
Customizable Options & Upgrades Available!

This harness features a Fender Custom Shop 3-Way Blade Switch to provide standard 3 Way pickup selections; this allows for Bridge/Bridge-Neck/Neck options.

These harnesses use CTS Precision Style full-size large pots (quarter size) with long shafts for body mounting. The tone pots are CTS push-pull pots for coil splitting; these are the longer life CTS pots with brass bushings in a space saving design. The volume pot is a standard CTS pot. If you are going through a guard or have a non-standard set-up, you may need additional nuts/washers (sold separately) or other modification. These pots work with most fine-knurled, 24-spline style knobs (sold separately). Audio Taper (“A” pot) or Linear Taper (“B” pot) and your choice of OHM styles are available and we offer your choice of OHM style: 250K or 500K.

The Coil Split Wiring incorporated into this harness allows you to split the coils on your humbucker in half, thus cutting one coil out and allowing your humbucker to perform a single coil (also known as Coil Cut or Coil Tap). Featuring two push-pull CTS pots, this unique harness allows for independent coil splitting so you can control each of your pickups separately while still maintaining separate volume control. Four wire pickups are required for a coil split to work. 

Note that we do not recommend selecting a 250K pot for use with a push-pull coil tapping pot (exercise extreme discretion!). We provide the option to choose a North Coil (cuts the South and leaves only the North Coil engaged) or South Coil (cuts the North and leaves only the South engaged) for each pickup.

Our tone control capacitors help produce balanced bass, middle, and treble. These harnesses use Sprague Orange Drop tone caps. Choose from 0.022uF (most often paired with 250K pots) or 0.047uF (usually used with 500K pots). If you prefer, we also offer Paper in Oil (Black Bee) Style of Tone Caps.

Harness jacks work with standard cables only and jack sockets accept standard ¼” plugs. Your choice:
*Mono Jack (9mm mounting hole; tightens to your jack plate)
*Stereo Jack (9mm mounting hole; tightens to your jack plate)
*Barrel Jack (12mm mounting hole; tightens inside of guitar)
*Switchcraft Jack (10mm mounting hole; tightens to jack plate)

Soldering is required for installation. We provide basic instructions posted in the item images to show the connections you’ll need to solder. Please know your abilities, requirements, measurements and needs fully to make sure this item will work for you. We are available to answer any questions before you buy.

*FCS Switch Height: 51.3mm
*FCS Switch Insertion Depth: 35.5mm
*FCS Switch Dimensions: 48.3mm (length) x 10.2mm (width)
*CTS Push-Pull Pot Shaft Length: 18/22mm (down/up positions)
*CTS Push-Pull Pot Dimensions: 24mm (diameter) & 44.5/48.5 (down/up overall height)
*CTS Push-Pull Pot Requirements: 10mm (hole diameter) & 25mm (cavity depth)
*CTS Pot Shaft Length: 18mm
*CTS Pot Dimensions: 24mm (diameter) & 31mm (height)
*CTS Pot Requirements: 10mm (hole diameter) & 12mm (depth)
*Switchcraft Jack Length: 13.4mm (without pins)
*Switchcraft Jack Diameter (mounting hole required): 10mm
*8” Insulated Wire Length
Variability is to be expected as measurements provided are approximations and based on the default options. Options selected will determine actual product measurements (listed separately). Ask any questions regarding options, measurements, installation, requirements, special requests, etc. prior to purchase.

*1 Prewired Guitar Wiring Harness Kit
Nothing else is included. Additional images may be provided for reference and comparison purposes only. There are no hard copy instructions or diagrams included. Basic directions are provided in the product images.

OPTIONAL ADDITIONS (Further Customize Your Harness!)
The Kill Switch Wiring Option allows you to interrupt the signal using an on-off, two-way toggle style mini-switch (~5.85mm diameter; 6mm hole required).

The Treble Bleed Volume Kit wiring modifier addresses the loss of high-end signal when turning down your volume pot. You’ll be able to keep more of your highs while maintaining volume adjustability. This wiring option allows a more constant tone throughout the range of your volume pot and helps remove the dark muddiness typically experienced in the lower volume pot settings.

Add an Onboard Effects (OBFX) to expand your playing and get more nuance out of every session. Our OBFX product pages detail these circuits and what they can do for your set-up. Active circuits require power. Adding an OBFX takes the place of one Tone Pot (replacement pot) and will move that push-pull pot to replace the volume pot.
*BCU (Active): Band Control Unit (Tone Shaper)
*EXP (Active): Expand to Peak Controller (Tone Expander)
*QDD2 (Active): Quadra Channel Sound Driver (Overdrive)
*QTB (Active): Quadra Tone Booster Driver (Tone Boost)
*TBX: Treble Bass Expander Control by Fender® (no battery)
*VTC (Active): VTB/VTC Tone Expander (Tone Overdrive)

Buyers assume all risk of use; sales are only offered to those competent to safely and lawfully purchase and use items.
ASK ANY QUESTIONS PRIOR TO PURCHASE. Due to the vast and varied nature of possible set-ups and user expertise, we do not provide specific information for every possible installation scenario. The provided BASIC instructions (posted in the item images, not sent as a hard copy with your order) will get you started. Please ask any questions before you buy if the posted instructions are not sufficient for your install or if you are unsure of your needs or ability to make modifications (if needed).
Note that we do not recommend installation using power tools as these can put too much force on the product and cause damage. Installation is best with moderate heat only (don’t have your iron too hot). Pay attention during install to avoid damage; components are sensitive. Excessive or prolonged heat can cause irreparable damage. This item is prewired. If your set-up requires you to disconnect the wires, be sure to take a picture or make note of the connections so you can reattach (solder!) properly. We do not recommend a clip/tie method for installation.
Inspect your order upon receipt. We will address any issues PRIOR to installation.

  • Item #: 1021

1V2T Prewired Harness, 2 Pup, CTS 1V+2T, DUAL Coil Split, Fender

Price: $74.95
* Marked fields are required.
Qty: *
Reviews (0) Write a Review
No Reviews. Write a Review